Easycontact S30
« Pour le sommaire
Product description
Zettex Easycontact S30 will bond a wide variety of substrates, including wood, metals, rubber, fabric, most plastics, cardboard, polythene and concrete, as well as
decorative laminates. It is ideal for permanent bonds that require good initial bond strength. It provides good temperature resistance and if protected from
contamination has an open time of several hours.
Material
SBR Rubber
Advantages
• Fast easy application
• Fast drying
• High solids
• High temperature resistance
• DCM Free
• Long Open Time
• Bonds a wide variety of surfaces
Zettex Easycontact S30 will bond a wide variety of substrates, including wood, metals, rubber, fabric, most plastics, cardboard, polythene and concrete, as well as
decorative laminates. It is ideal for permanent bonds that require good initial bond strength. It provides good temperature resistance and if protected from
contamination has an open time of several hours.
Material
SBR Rubber
Advantages
• Fast easy application
• Fast drying
• High solids
• High temperature resistance
• DCM Free
• Long Open Time
• Bonds a wide variety of surfaces
Available forms
• Barrel 2.5 KG, 5 KG , 10 KG, 25 KG, 50 KG, 200 KG en 1000 KG
Colour
• Clear or Red.
• Barrel 2.5 KG, 5 KG , 10 KG, 25 KG, 50 KG, 200 KG en 1000 KG
Colour
• Clear or Red.
Applications
• Zettex S30 dries in two minutes under normal conditions, but this will vary under different temperatures and humidities. High humidity and low temperatures will slow the drying time and if the temperature gets very low, can produce bloom. Bloom is moisture which forms on the glue line caused by solvent evaporation lowering the air temperature above it. Do not use on flexible PVC or expanded polystyrene.
Below you will find the directions for use.
1. Surfaces should be clean, dry and free from grease, oil and dust. Excessive dust will impair performance.
2. When the adhesive is dry to the touch it is ready for the bond to be made.
3. Porous substrates may require two applications
4. Drying takes approximately 1 to 2 minutes depending on substrates, ambient temperature and humidity. Over spraying and pooling of the adhesive will increase the drying time and may cause the adhesive to show through the laminate.
5. It is important to remember that Zettex S30 is a contact adhesive and forms a bond by sticking to itself, so there must be sufficient adhesive on both surfaces for this to happen.
6. Allow the adhesive to tack up and protect from contamination whilst this happens. The adhesive is ready to bond when it feels dry to the touch and does not transfer.
7. Once the two surfaces have been brought together, and aggressive bond will be made. Spacers can be used to ensure the surfaces do not come into contact prematurely.
8. Once the two surfaces are brought together, apply a uniform pressure over the work piece, starting in the middle and working outwards. Use blocks or a 3 inch roller and ensure the whole piece has been worked to ensure adequate contact of the adhesive.
9. Pay particular attention to the edges. Please note that testing at this point by lifting the edge will weaken the bond. A nip roller will give the best results.
10. Once assembled, the piece can be machined or trimmed as required.
11. Full cure will take 24 hours.
• Zettex S30 dries in two minutes under normal conditions, but this will vary under different temperatures and humidities. High humidity and low temperatures will slow the drying time and if the temperature gets very low, can produce bloom. Bloom is moisture which forms on the glue line caused by solvent evaporation lowering the air temperature above it. Do not use on flexible PVC or expanded polystyrene.
Below you will find the directions for use.
1. Surfaces should be clean, dry and free from grease, oil and dust. Excessive dust will impair performance.
2. When the adhesive is dry to the touch it is ready for the bond to be made.
3. Porous substrates may require two applications
4. Drying takes approximately 1 to 2 minutes depending on substrates, ambient temperature and humidity. Over spraying and pooling of the adhesive will increase the drying time and may cause the adhesive to show through the laminate.
5. It is important to remember that Zettex S30 is a contact adhesive and forms a bond by sticking to itself, so there must be sufficient adhesive on both surfaces for this to happen.
6. Allow the adhesive to tack up and protect from contamination whilst this happens. The adhesive is ready to bond when it feels dry to the touch and does not transfer.
7. Once the two surfaces have been brought together, and aggressive bond will be made. Spacers can be used to ensure the surfaces do not come into contact prematurely.
8. Once the two surfaces are brought together, apply a uniform pressure over the work piece, starting in the middle and working outwards. Use blocks or a 3 inch roller and ensure the whole piece has been worked to ensure adequate contact of the adhesive.
9. Pay particular attention to the edges. Please note that testing at this point by lifting the edge will weaken the bond. A nip roller will give the best results.
10. Once assembled, the piece can be machined or trimmed as required.
11. Full cure will take 24 hours.
| Propriété | Spécification |
|---|---|
| Solvent | Diethyl ether |
| Solids Content (approx.) | 65 % |
| Colour | Clear or Red, other colours available on request |
| Heat Resistance | 90℃ |
Télécharger le fichier MSDSTélécharger le fichier TDS
Poser une question
Rappelez-moi